Welcome back to the Finlayson Sew-Along!  We get to start sewing today!  I will be adding the optional Decorative Facing to both sweater Variations and then we will sew the shoulder seams. DSC03476 Begin by stay stitching along the lower facing edge using a 5/8" seam allowance and a regular length straight stitch.  This stitching will help you create a smooth curve and even seam allowance when you iron under the seam allowance. DSC03479 Next, clip up to the stitching line at regular intervals along the sharpest area of the curve.  I find using sharp embroidery scissors to be the most accurate way of clipping up to the stitches like this - it is easy to clip into the stitching by accident, so be careful with each snip!. DSC03481 Press the entire curve under as evenly as possible so that the stitching is hidden on the wrong side of the Decorative Facing.DSC03486 You can see that the clips you made in to the stitching allow the seam allowance to overlap slightly so that the outer edge of the curve can be manipulated into this smaller area. DSC03487 If you would like to apply a garment tag or other sort of decoration, now is the time!  I top stitched a Thread Theory tag and a square of contrast fabric to my Facing for Variation 1: DSC03491 ...and one of the lovely Sewaholic garment tags along with a 3" piece of velvet ribbon (as a hanger) to my Facing for Variation 2:DSC03489 To attach the Decorative Facing to the sweater Back, pin the facing so that it is even with the neckline's raw edge so that the wrong sides are together (so that the facing will be on the inside of the sweater).DSC03492 Top stitch around the entire facing - make sure not stretch one fabric layer more than the other! DSC03501 With the Decorative Facing applied, we're now ready to sew the shoulder seams. First, let's begin by deciding which method of stabilization to use!  Have a look at the post on materials if you haven't already.  There are some close up pictures of the materials for you to examine.  For Variation 1 I will use Option 1 (from the instruction booklet) and apply rayon hem tape (you could use the ribbon, twill tape, clear elastic, or stay tape with the same results). Apply the tape to the sweater Back by centering the tape over the seam line and pin the sweater Front and sweater Back with right sides together.  Sorry, I didn't get a photo of the tape and fabric layers pinned.  But you can see a similar photo when I show you Variation 2 in a little bit!  For Variation 1, I am using a reinforced stretch stitch (otherwise known as a triple stitch) to stitch all seams.  This is the lower stitch in the photo below - it looks like a straight stitch.  While the reinforced stretch stitch isn't the best option for delicate knits, most medium weight knits can handle it just fine.  For this stitch, the needle moves backwards and forwards to stitch over the same area three times so the stitch is very strong and can be pulled without snapping (important for knit garments!).  It can wear delicate fabrics out though since the needle punches into the same spot so many times, so test it on a scrap first! DSC03515 I am finishing the seam allowances with a wide zig zag stitch.  If you prefer, you can use a narrow zig zag stitch to sew all your seams (rather than the reinforced stitch) and then a wider zig zag stitch to finish the seam allowance. Here is how my finished shoulder seam looks: DSC03513 And from the front of the sweater:DSC03511 Once the shoulder seam has been sewn and the seam allowances have been finished, press the shoulder seam open. DSC03519 I like to topstitch along either side of my shoulder seams to keep the seam allowances pressed flat.  It looks quite pretty from the right side and helps to reinforce the shoulder seam even further to prevent it from stretching out when the sweater is worn.DSC03517 And now, on to Variation 2!  For this variation, I will use Option 2 (from the instruction booklet) and apply a strip of silk lining.  I'll be using my serger to sew this sweater.  Here you can see the three layers (Sweater Front, Sweater Back and the silk lining) all pinned together: DSC03508 Stitch through all three layers.  If you are using a serger, make sure to use the 5/8" seam allowance - you will be cutting the excess seam allowance off with your serger blade. DSC03521 If using a serger, press the finished seam allowance towards the back (this covers the fabric or tape you've used to reinforce the seam). DSC03526 I top stitched the seam along the back for this sweater but not along the front (because there is no seam allowance along the front):DSC03524 Our Facings and Shoulder Seams are finished!  Join us next Monday so that we can sew the collar and hood - our sweater will really begin taking shape at that point.  Have a lovely weekend!

Comments

Rebecca Porter

Rebecca Porter said:

Top answer, thank you! Nice to know I’ve not been a complete sewing rebel by using a straight stitch on my side and shoulder knit seams ;)

ThreadTheory

ThreadTheory said:

I always think that when it comes to sewing, the ‘right’ way is the way you find works best for you :D.

Finlayson Sew-Along: Preparing and sewing the collar or hood | Thread Theory

Finlayson Sew-Along: Preparing and sewing the collar or hood | Thread Theory said:

[…] to the schedule, it’s a big day for us Finlayons sewists today!  On Friday we sewed our Decorative Facing and shoulder seams; today we will be moving on to perhaps the trickiest part of this sweater – the collar or […]

Rebecca Porter

Rebecca Porter said:

Hey, I’m just about to start my Finlayson (better late than never!), but I had a quick question which is something I’ve always wondered about knits. We reinforce the shoulder seams to stop them stretching, so why do we then sew them using a stretch stitch? And is it important to sew all of the seams that won’t need to stretch (e.g. side and underarm seams) with a stretch stitch?
Thanks in advance! Becca

ThreadTheory

ThreadTheory said:

Good question! Depending on what type of material you use to reinforce your shoulder seams, you are right, you don’t necessarily need a stretch stitch. I like to recommend using one though in case the material you are using still contains some stretch. For instance, if you were to reinforce your shoulder seams with a knit selvedge, thin interfacing, or clear swimsuit elastic, you would need to use a stretch stitch so that the seam can stretch as much as the material used. If you were to use rayon hem tape or a woven scrap of fabric, you are right, the stretch stitch would no longer be necessary because the seam would no longer be able to stretch!

As for sewing the seams that won’t need to stretch – here is the guideline that I learned in school for knits: Vertical seams (such as the ones you mentioned) can be sewn with whatever stitch works best with the fabric (be it serging, a straight stitch or a reinforced stretch stitch) and horizontal seams need to be sewn with a stretchy enough stitch to match the stretch of the fabric (serging, a zig zag, or for more stable knits, a reinforced stretch stitch). Horizontal seams generally include cuffs, hems and neck openings.

I hope this helps! Please feel free to ask any other questions your might have :).

Leave a comment

Please note: comments must be approved before they are published.